RICOH AP3800C DRIVER

With the clip lifted, turn the augur clockwise Remove the cables and then these two screws – this will release the bracket and HDD from the unit. The two programme chips are easy to remove – press down on the catch to release the boards. If you have the printer version, then the pcb and the HDD will already be visible at this point. The white pin which protrudes from the end of the augur will fall out in the absence of the spring, so try to keep it in place as it’s not so easy to persuade back in on account of its shape. Ideally, at this point, get a friend to replace the screws whilst you maintain the pressure on the bar – although it is possible to achieve this single handed. Color quality is a little shy of best-of-breed color lasers notably the Xerox Phaser DN we reviewed in our October 30, issue.

Uploader: Grogor
Date Added: 6 April 2010
File Size: 68.33 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 51670
Price: Free* [*Free Regsitration Required]

Re-assemble the whole unit and switch on.

Ideally, at this point, get a friend to replace the screws whilst you maintain the pressure on the bar – although it is possible to achieve this single handed. The panel can then be pulled out of the machine using the aap3800c.

Aficio APC Downloads | Ricoh Global

We review products independentlybut we may earn affiliate commissions from buying links on this page. With the clip lifted, turn the augur clockwise Step 3 With the CMF version, it is necessary to remove the expander board first. If you know otherwise, please let me ap3800 As a precaution, I will endeavour to ensure that the machine is in the ready mode before sending data in future.

Last Drivers  SANGOMA A200 DRIVER DOWNLOAD

Ricoh Aficio AP3800C Workgroup Laser Printer

There’s no customized user interface either, but it does the the job. Make sure they are fully pushed home when inserting them into the ap380c controller board. The problems turned out to be minor, although rather strange in nature. You can then pull the augur off the end of the unit.

Step 1 Remove the two screws which secure the controller unit to the machine. The client software for workstations fares better on usability, with a self-explanatory print monitor feature that lets users see the printer status and access loads of output options duplex, booklet, sorting, stapling, and so on. The pin of a new unit is released as the motors turn and this changes the state of the switch from open to closed.

Aficio APC download page

The issue is apparently a known one – it can also occur if a black and white job is sent immediately after start up – and is related to earlier versions of the engine firmware. The Service Manuals for this machine are quite comprehensive, although perhaps a little confusing because of the various different options. After various experiments I found the solution was to move both the programme chips and the NVRAM chip from my existing faulty controller onto the replacement board.

The ap8300c needs to be located carefully, pushed on and then turned a little counterclockwise until it clicks into place. Using this sheet and the SPX adjustments, has enabled me to make a considerable improvement in the output of my If you have a printer only ricohh of thethen the chances are you will a3800c little use of the Ticoh, but it can be replaced with a suitable IDE drive from 20GB upwards not sure if there is an upper limit, but 30, 40 and 80GB drives all worked.

Last Drivers  ALBATRON PM73V DRIVER

There is a tool available for pulling chips, but as long as you’re careful, it can be done without. They don’t pick up the various options on the copier, so you have to go into the driver and enable the duplexer, finisher, extra trays etc. It was a complete controller section which had been pulled from a machine being broken for spares.

In the end, it went away of its own accord once the machine had cooled down over night. Clearing the error code proved troublesome – I tried ap3800x the synchronizing detector boards which the sc indicates as being the cause of the problem but that made no difference. The postscript divers above are from the Ricoh website, although they are a bit basic.

Be very gentle with this as it could easily break if you lever too hard with the screwdriver. In graphics, this sometimes showed as obvious banding.

Remove the two screws which secure the controller unit to the machine. Press the yellow “Clear Modes” key 2. The SP mode is accessed from the copier panel as follows: As the HDD is an option, it was possible to get some functionality back simply be disconnecting the faulty pa3800c. Welcome to Michel’s Place michelsplace, michelsplace.

Color quality is a little shy of best-of-breed color lasers notably the Xerox Phaser DN we reviewed in our October 30, issue.